Quantcast
Channel: Nissanhelp.com Forums
Viewing all 7823 articles
Browse latest View live
↧

Answered: P0420 2006 Nissan Maxima -

April 17, 2016, 9:20 pm
$
0
0
How to Set Diagnostic Test Mode II (Self-diagnostic Results)
1. Confirm that accelerator pedal is fully released, turn ignition switch ON and wait 3 seconds.
2. Repeat the following procedure quickly five times within 5 seconds.
a. Fully depress the accelerator pedal.
b. Fully release the accelerator pedal.
3. Wait 7 seconds, fully depress the accelerator pedal and keep it for approx. 10 seconds until the MIL starts
blinking.

Do not release the accelerator pedal for 10 seconds if MIL may start blinking on the halfway of this
10 seconds. This blinking is displaying SRT status and is continued for another 10 seconds. For
the details, refer to EC-56, "How to Display SRT Status" .
4. Fully release the accelerator pedal.
ECM has entered to Diagnostic Test Mode II (Self-diagnostic results).

More...
↧
Search

Answered: what do codes p0103 & p1102 mean for a 2003 nissan altima 3.5?

April 17, 2016, 9:20 pm
$
0
0
Hi there,

Both of these codes are for the mass air flow sensor. Its usually burned out inside when you have this code. Your symptoms are exactly what to expect when the maf sensor fails as well. I suggest replacing the sensor.

More...
↧
↧

What's causing my 2001 Nissan Xterra to get codes p0300 and p0 335?

April 18, 2016, 9:30 am
$
0
0
What's causing my 2001 Nissan Xterra to miss at high rpms and give the codes p0300 and Po335? It stalled on me then wouldn't start.nxt day started fine but smelled like it was running rich .the idle also flucuates. Please help

More...
↧

2004 Nissan xterra 3.3 l p1456 p0442 and p1706

April 18, 2016, 3:28 pm
$
0
0
Does anyone have any suggestions on how to clear these codes? I have had my xterra since February and it's been one thing after another. I love it, and I just want a fresh inspection s ticker on it. It won't pass emissions with 3 codes! Help!
↧

Answered: Random misfire 2006 nissan maxima Ls 3.5

April 18, 2016, 9:41 pm
$
0
0
Unfortunately there are many things that could cause the P0300 code, probably the most common cause for the code are the ignition coils. Even new aftermarket coil can trigger that code.

Here is a list of all the things that could cause the code:

- Faulty spark plug (s)
- Faulty ignition coil (s)
- Clogged or faulty fuel injector (s)
- Intake air leak
- Fuel injectors harness is open or shorted
- Fuel Injectors circuit poor electrical connection
- Ignition coils harness is open or shorted
- Ignition coils circuit poor electrical connection
- Insufficient cylinders compression
- Incorrect fuel pressure

Read more: P0300 NISSAN Cylinder Misfire Detected Random Cylinders | AutoCodes

More...
↧
↧

Answered: What's causing my 2001 Nissan Xterra to get codes p0300 and p0 335?

April 18, 2016, 9:41 pm
↧

Sup,new on here.. Looking for a little help..

April 19, 2016, 7:42 am
$
0
0
Okay, I have 95 D21 and it was running great shape. I drove it around to about 6 stops then on the last stop/go it wouldn't start..?? Took the starter of(was replaced in the last 6 mths)and was fine,put my screwdriver across it and it cranked..everything on motor has been replaced..BUT i noticed that horn,interior lights,hazard lights wont work.. could it be as simple as computer?? Anybody have ANY suggestions?? Going back to pick it up now,it would be nice to have some direction,if not thanks anyway..

Art
↧

where is the sensor P0717 nissan pathfinder SE?

April 19, 2016, 9:50 am
$
0
0
my question is scanned and the failure of a Nissan brand sensor failure P0717, where this senaor inside or outside the transmission?

More...
↧
Search

Driver-side Door and Window issues

April 19, 2016, 4:38 pm
$
0
0
Hello all,

I searched briefly and did not see a thread so please direct me to one if it exists.

My driver side door will not fully unlock and so it will not open. When I try to unlock the door, the little lock indicator on the inside door handle will not go fully to the unlock position.

Also, my driver side window will roll back down half-way when I roll it up, or it will get stuck when it is fully down. In both cases for the window, it seems to be only when using the auto function. I just had the motor replaced by the way.

Any help would be greatly appreciated!

Edit: 2004 350z roadster.
↧
↧

2001 Altima driver power seat

April 19, 2016, 6:30 pm
$
0
0
I recently purchased a 2001 Altima that had minor issues and started fixing it up. It's amazing that no one wanted to buy this car because it had no radio in it. Anyway, I needed a few wiring diagrams for the hazards lights, radio, fog lights, and drivers power seat. I bought a Haynes manual and it had all those diagrams except the drivers power seat diagram. Everything else is fixed, so now I need to tackle the seat issue. The seat is fully back and won't go forward. Does anyone have this diagram or know where I can get it from? I have a suspicion it is the motor, but would really like to confirm that before I spend my money on that and the switch be bad.
↧

Answered: where is the sensor P0717 nissan pathfinder SE?

April 19, 2016, 9:50 pm
$
0
0
Hi there,

The revolution sensors are inside the transmission on this model year.

More...
↧

Answered: how do i fix the p0110 on my nissan 240sx

April 20, 2016, 1:30 pm
$
0
0
Hi there,

This code is usually resolved when you replace the intake air temp sensor. On the older 240s the sensor is a 2 wire sensor before the air cleaner. On the newer models it's part of the mass air flow sensor. You can tell based on the number of wires to the maf sensor. If it is a 5 wire sensor, then the IAT is part of that sensor.

More...
↧

ignition coil burning

April 21, 2016, 10:07 am
$
0
0
I have a 2005 Nissan Murano 3.5L . Cylinder #1 keeps burning this coil when the trigger wire at the computer is clipped coil stops burning. Ive read lots of forums where the computer was replaced and problem still persists just wondering if anyone has come acroos the answer yet.
↧
↧

Answered: P1051 NISSAN -quest

April 22, 2016, 7:20 am
$
0
0
Hi there,

There is no recall for this sensor or this code. This code is for the heater circuit of the bank 1 O2 sensor. This is mounted in the exhaust manifold on the firewall side of the engine. The most common repair is replacing the sensor.

More...
↧

Nissan altima 2.5s alignment specs and front bumper rebar ride hight specs

April 22, 2016, 9:54 am
$
0
0
Car hit on pss side front needto check frame horn position rebar hight to begin repair
↧
Search

new throttle body still want idle over 2500 r so on 2004 nissan sentra 1,8

April 24, 2016, 2:10 pm
$
0
0
put different pedal assy shows code 2128 and 2138 will crank idle till warm and then surges and still want go over 2500 and sometimes uo 3200 I can un plug TB and still will throttle up the same way any help?

More...
↧

2011 xterra radio front removal

April 25, 2016, 9:41 am
$
0
0
Hi, my 2 year old put coins in my cd slot and the cd won't play. How can I remove the front of the radio ? Will we be able to retrieve the coins ? I hear a few rattling. :(oh the cd came out luckily but naturally won't fully go back in
TIA
↧
↧

'94 Altima occasional hard start

April 25, 2016, 4:16 pm
$
0
0
Hi folks,

Every now and then my '94 Altima GXE will take prolonged cranking and some throttle before it starts. In most cases, cranking the engine without pressing the throttle starts the car fine.

The car runs great once it starts. Symptoms:

- With a cold engine, especially in the morning, it always starts immediately.
- With a hot engine (run in and out of the store) it mostly starts immediately.
- With a warm engine, after it has sat for 15mins-an hour or more, it will crank longer and needs some throttle. It will always start though.

Clearly there is a temperature factor in play here. A warm but not hot engine will make starting more difficult. A cold or hot engine, starts the car immediately.

Repairs so far: replaced injectors (the old ones were in bad shape) cleaned the EGR valve and tested it by applying vacuum. The engine throws a bad knock sensor code (can someone tell me how to replace the darn thing?), but that does not illuminate the engine check light. Spark plugs are less than 2 years and 7Kmiles old, spark plug wires are new, OEM. Distributor suffered the dreaded oil leak two years ago and was replaced by the dealer at much $$$.

Any ideas? I have not tried replacing the fuel filter yet, it is next on my agenda.
To me it seems like a fuel delivery issue. Fuel pump? Fuel pressure regulator?

Thanks.
↧

New PCV&4 O2 sensors heat&mon OK;ECM clear 3 different ways why is 2004 nissan maxima 3.5 SES 1273?

April 26, 2016, 5:50 am
$
0
0
Three Months ago just as it was being inspected, my 2004 Nissan Maxima 3.5 lit up a service engine soon (SES) light which read as p1800 VIAS Solenoid and p0037 o2 sensor 2 bank 1 and those were replaced and cleared the ECM. after 30 miles the SES lit up with new codes C1130 crank sensors, p0726 TPI and engine speed sensors and 1273 O2 sensor 1 bank 1 and with all intent to order everything, I went out and read the codes again and only the 1273 code remained so I replaced all the remaining bank 2 O2 sensors as well as the pain in the butt sensor 1 bank 1 between the engine and fire wall and did so with a special open socket for the job so it is properly seated and is not cracked. while I was there I replaced the PCV valve and filters as such were indicated as a possible problem. I then did separate ECM clearing-- gas pedal code--disconnect battery for two hours with terminals touching-- and MAF code and Actron Reader to erase codes in ECM. I inspected for vacume, intake, and exaust manifold leaks and cooling fluid/oil mixings and all is good. I even traced the wires looking for evidence of wire failure or corrosion and again all looks good.Two months later this car is still SES-ing a 1273. With all new OEM O2 sensors, new PCV, codes cleared 3 different ways, and o2 Heat&Mon OK why is my 2004 nissan maxima 3.5 is still SES-ing 1273 ?

More...
↧

Sentra acceleration issue

April 26, 2016, 4:58 pm
$
0
0
I have a 2001 Sentra GXE 1.8L that the alternator went out on, so I replaced it. As soon as I started the car it had no power and wouldn't rev past 3500 rpm. I checked everything was reconnected properly. It started to improve and will drive at part throttle fine, but if you try to use anything more than half throttle the car stumbles, and seems to cut out. I tried reinstalling the old alternator and same results, At first there was no CES but the light came on and my Innova scanner fails to connect with the computer. I don't know if these are related,
↧
Viewing all 7823 articles
Browse latest View live
Search